View MC14601207_829096.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Freescale Semiconductor Technical Data
Document Number: MC146012 Rev. 1.0, 5/2007
Low Power CMOS Photoelectric Smoke Detector IC
The MC146012 is an advanced smoke detector component containing sophisticated very-low power analog and digital circuitry. The IC, when used with an infrared photoelectric chamber and a small number of external components, will detect smoke by sensing scattered light from smoke particles. When detection occurs, a pulsating alarm is sounded via on-chip push-pull drivers and an external piezoelectric transducer. The MC146012 provides both audible and visual alarms. Upon sensing a normal smoke level, both alarms will be activated. It is possible to mute the audible alarm for approximately eight minutes through the Integrated Mute Function (IMF), although the LED will continue to flash at a high rate. This feature is resetable through a pushbutton test. The IMF feature will be overridden by remote smoke, high smoke level, timeout or reset. The Alarm memory feature will allow for identification of an alarming detector. Through a pushbutton test, the LED will flash rapidly if there was a previous alarm condition detected at the unit. The variable-gain photo amplifier allows direct interface to IR detector (photodiode). The gain settings are determined by external capacitors and compensation resistors. A two stage speed-up is incorporated into the smoke monitor to minimize time and help reduce false triggering. Further reduction of false triggering is also addressed with the double sample chamber sensitivity and double I/O sample. Features * * * * * * * * * * * Integrated Mute Function (IMF) to Temporarily Disable Horn Alarm Memory to Help Identify Alarming Unit Speed-Up Sampling Rate After First Detection of Smoke Double Sample for Degraded Chamber Sensitivity Monitor Digital Noise Filter on the I/O Pin Power-Up and Power-Down RESET Low-Battery Trip Point Set Externally Temporal Horn Pattern Operating Temperature: -10 to 75C Operating Voltage Range: 6.0 to 12 V Average Supply Current: 6.5 A ORDERING INFORMATION
Device MC146012ED -10 to 75C MCZ146012EG/R2 SOIC Package Temp. Range Package Plastic Dip
MC146012
LOW POWER CMOS PHOTOELECTRIC SMOKE DETECTOR IC
16 1
ED SUFFIX PLASTIC DIP 98ASB42431B
16 1
EG SUFFIX SOIC PACKAGE 98ASB42567B
(c) Freescale Semiconductor, Inc., 2007. All rights reserved.
C1 C2 2 1 DETECT 3 AMP VDD - 3.5 V VDD - 4.0 V REF GATE ON/OFF TIMING LOGIC COMP + LOW SUPPLY ALARM, MUTE, & RESET LOGIC
SMOKE
7
I/O
ZERO
GAIN
8 HORN MODULATOR AND DRIVER 9 10 6 11
BRASS SILVER FEEDBACK IRED LED
OSC
12 13
OSC
R1 16 TEST 4
GATE ON/OFF
VDD - 5.0 V REF COMP + PIN 5 = VDD PIN 14 = VSS
STROBE
LOW-SUPPLY 15 TRIP
Figure 1. Block Diagram
C1 C2 DETECT STROBE VDD IRED I/O BRASS
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
TEST/MUTE LOW-SUPPLY TRIP VSS R1 OSC LED FEEDBACK SILVER
Figure 2. Pin Assignment (16-Pin DIP)
MC146012 2 Sensors Freescale Semiconductor
Table 1. Maximum Ratings(1) (Voltages Referenced to VSS)
Symbol VDD VIN DC Supply Voltage DC Input Voltage C1, C2, Detect Osc, Low-Supply Trip I/O Feedback Test Parameter Value -0.5 to +12 -0.25 to VDD +0.25 -0.25 to VDD +0.25 -0.25 to VDD +10 -15 to +25 -1.0 to VDD +0.25 10 25 +25 Forward -150 Reverse in Stil Air, 5 sec. Continuous 1200(2) 350(3) -55 to +125 -25 to +75 260 Unit V V
IIN IOUT IDD PD Tstg TA TL
DC Input Current, per Pin DC Output Current, per Pin DC Supply Current, VDD/VSS pins (15 Seconds in Reverse Dir.) Power Dissipation Storage Temperature Operating Temperature Lead Temperature, 1 mm from case for 10 seconds
mA mA mA mW C C C
1. Maximum ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the limits in the electrical characteristics tables. 2. Derating: -12 mW/C from 25C to 60C. 3. Derating: -3.5 mW/C from 25C to 60C.
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of voltages any higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to a range of VSS (VIN or
VOUT) VDD except for I/O pin which can exceed VDD, and the Test/Mute input, which can go below VSS. Unused inputs must always be tied to an appropriate logic voltage level (e.g. either VSS or VDD). Unused outputs and/or an unused I/O must be left open.
Table 2. Electrical Characteristics (Voltages Referenced to VSS, TA = -10 to 60C unless otherwise indicated.)
Symbol VDD VTH IDD Parameter Power Supply Voltage Range Supply Threshold Voltage, Low Supply Alarm Average Operating Supply Current (per Package) (Does not include Current through D3-IR Emitter) Peak Supply Current (per Package) (Does not include IRED Current into base of Q1) Low Supply Trip: VIN = VDD/3 Standby Configured per Figure 5 During Strobe On, IRED Off Configured per Figure 5 During Strobe On, IRED On Configured per Figure 5 Test Condition Test Pin -- 15 -- -- -- -- 7.0 10 16 16 7.0 10 16 VIN = VSS or VDD VIN = VSS or VDD VIN = VSS or VDD VIN = VSS or VDD VIN = VSS or VDD 3.12 15 10 16 16 VDD -- -- 12 9.0 12 12 9.0 9.0 9.0 9.0 9.0 9.0 9.0 12 12 12 12 12 Min 6.0 7.2 -- -- -- -- -- -- -- 2.0 3.2 6.3 8.5 -100 -100 -100 -100 -100 Max 12 7.8 9.0 7.0 1.25 2.5 1.5 2.7 0.5 VDD-2.0 -- -- -- +100 +100 +100 +100 -1.0 V Unit V V A
IDD
mA
VIL
Low Level Input Voltage
I/O Feedback Test Test I/O Feedback Test OSC, Detect Low-Supply Trip Feedback Test
VIM VIH
Mid Level Input Voltage High Level Input Voltage
V V
IIN
Input Current
nA
IIL
Test Mode Input Current
A
MC146012 Sensors Freescale Semiconductor 3
Table 2. Electrical Characteristics (Voltages Referenced to VSS, TA = -10 to 60C unless otherwise indicated.) (continued)
Symbol IIH Pull-Down Current Parameter Test I/O Test Condition VIN = VDD I/O VIN = VDD I/O VIN = 17 V Test Pin 16 7.0 VDD Min Max Unit
12 9.0 9.0 12 6.5 6.5 6.5 -- 9.0 6.5 12 12 6.5 -- -- --
-- 0.5 25 -- -- -- 5.5 VDD-0.1 VDD-5.4 -4.0 -- -- -- VDD-4.0 VDD-3.9 VREF0.52
-1.0 1.0 100 140 0.6 1.0 -- -- VDD-4.6 -- -16 100 0.5 VDD-2.0 VDD -3.1 VREF-0.48
A A
VOL VOH VOUT
Low-Level Output Voltage High-Level Output Voltage
LED Silver, Brass Silver, Brass
IOUT = 10 mA IOUT = 16 mA IOUT = -16 mA Inactive, IOUT = 1.0 A Active, IOUT = 100 to 500 A (Load Regulation) Local Smoke, VOUT = 4.5 V Local Smoke, VOUT = VSS (Short Circuit Current) VOUT = VSS or VDD 1.0 mA
11 8.9 8.9 4.0 9.0 7.0 -- 11 -- -- -- --
V V V
Output Voltage Strobe (For Line Regulation, See Pin Descriptions) High-Level Output Current I/O
IOH
mA
IOZ VOL VIC VREF
Off-State Output Leakage Current Active Common Mode Voltage Range Smoke Comparator Reference Voltage
LED
nA V V V V
C1, C2, Detect Internal Internal
Local Smoke, Pushbutton, or Chamber Sensitivity Test Local Smoke, Pushbutton, or Chamber Sensitivity Test Local Smoke, Pushbutton, or Chamber Sensitivity Test
VREF-HI High Smoke Comparator Reference Voltage * TA = 25C Only
Table 3. AC Electrical Characteristics (Refer to Timing Diagram Figure 3 and Figure 4. TA = 25C, VDD = 9.0 V, Component Values from Figure 5.)
No. 1 2 3 4 5 Symbol 1/fOSC tLED Parameter Oscillator Period LED Pulse Period Test Condition Free-running Saw tooth Measured at Pin 12 No Local Smoke, and No Remote Smoke Remote Smoke, but No Local Smoke Local Smoke Pushbutton Test Push button Test with Alarm Memory 6 7 8 9 tw(LED), tw(stb) (tIRED) LED Pulse Width and Strobe Pulse Width (IRED Pulse Period) Remote Smoke but No Local Smoke Smoke Test Chamber Sensitivity Test, Without Local Smoke Local Smoke, in Speed-Up Pushbutton Test 10 11 12 tw(IRED) tR tF IRED Pulse Width Clocks 1.0 4096 -- 256 256 4.0 1.0 1024 4096 128 128 Tf * -- -- Min(1) 7.2 28.8 -- 1.6 1.6 25.6 OFF 7.2 28.8 0.9 0.9 94 -- -- Typ(2) 8.0 32.4 Extinguished 2.0 2.0 32 -- 8.1 32.4 1.0 1.0 -- -- -- Max(1) 8.8 35.2 -- 2.4 2.4 38.4 OFF 8.8 35.2 1.1 1.1 116 30 200 s s s ms -- s Unit ms s
MC146012 4 Sensors Freescale Semiconductor
Table 3. AC Electrical Characteristics (Refer to Timing Diagram Figure 3 and Figure 4. TA = 25C, VDD = 9.0 V, Component Values from Figure 5.) (continued)
No. 13 14 15 16 17 18 19 20 21 22 23 tMUTE Symbol tON tOFF tOFFD tCH tW(CH) tRR tstb Silver and Brass Chirp Pulse Period Silver and Brass Chirp Pulse Width Rising Edge on I/O to Smoke Alarm Response Time Strobe Out Pulse Period Low Supply or Degraded Chamber Sensitivity Low Supply or Degraded Chamber Sensitivity Remote Smoke, No local smoke Smoke Test Chamber Sensitivity Test Without Local Smoke Low Supply Test Without Local Smoke Pushbutton Test/Speed-Up Parameter Silver and Brass Temporal Modulation Pulse Width Test Condition Clocks 64 64 192 4096 1.0 -- 1024 4096 4096 -- -- Min(1) 0.45 0.45 1.35 28.8 7.2 -- 7.2 28.8 28.8 -- 6.0 Typ(2) 0.5 0.5 1.52 32.4 8.0 2.0(3) 8.1 32.4 32.4 1.0 8.0 Max(1) 0.55 0.55 1.65 35.2 8.8 -- 8.8 35.2 35.2 -- 11 s ms s s s s s min Unit s
1. Oscillator period T (T = Tr + Tf) is determined by the external components R1, R2 and C3 where Tr = (0.6931)R2*C3 and Tf = (0.6931)R1*C3. The other timing characteristics are some multiple of the oscillator timing shown in the table. The timing shown should accommodate the NFPA72, ANSI S3.41, and ISO8201 audible emergency evacuation signals. 2. Typicals are not guaranteed. 3. Time is typical-depends on what point in cycle the signal is applied.
MC146012 Sensors Freescale Semiconductor 5
6
1
MC146012
OSC (Pin 12)
22
Low Supply Test (Internal)
Chamber Test (Internal)
8
Photo Sample (Internal)
IRED (Pin 6)
7 7
Strobe (Pin 4)
20 21 22
LED (Pin 11)
2 6 11 16 16
Figure 3. Typical Standby Timing Diagram MC146012 Device
Silver, Brass Enable (Internal) Power-on Reset No Low Supply - Chamber Sensitivity OK Chirps Indicate Low Supply
Notes: Numbers refer to the AC Electrical Characteristics Table Illustration is not to scale.
Sensors Freescale Semiconductor
Chirps Indicate Degraded Chamber Sensitivity
LED
HORN
IRED
STROBE_ENA
HI_SMOKE
CHMFAULT
IO
SMOKE
TEST_IN
CH1 600u Time (Seconds) 650u 700u 750u
LB1
Figure 4. Typical Local Smoke Timing MC146012 Device
HUSH
MC146012 Sensors Freescale Semiconductor 7
Silence Feature (Option) C1 R8 8.2 k R9 5.0 k C2 C4 22 F + 9.0 V B1 D1 Reverse Polarity Protect. SW1 Circuit Pushbutton Test C1 TEST & SILENCE C2 DETECT STROBE LOWBATT VSS C3 = 1500 pF R1 R1 = 100 k OSC LED I/O BRASS FEEDBACK SILVER R4 = 2.2 M C6 0.01 F HORN X1 R5 = 100 k R2 = 10 M R3 = 470 D4 R7 47 k Visible LED SW2 R16 = 3.0 M Silence Button R6 100 k
R15 R14
1 M R11 D2 IR Detector
R10 4.7 k R12 1.0 k C5 100 F
IR Emitter D3 Q1 IR Current 4.7 to 22
MC146012
VDD IRED
To other MC146012(s) Escape light(s) Auxiliary Alarm(s) Remote(s) And/Or Dialer
Figure 5. Typical Battery Powered Application
# * ** Values for R4, R5 and C6 may differ depending on type of horn used. C2 and R13 are used for coarse sensitivity adjustment. Typical values are shown. R9 is for fine sensitivity adjustment (optional). If fixed resistors are used, R8 = 12k, R10 is 5.6k to 10k and R9 is eliminated. Components necessary to utilize IMF feature.
MC146012 8 Sensors Freescale Semiconductor
PIN DESCRIPTIONS
C1 (PIN 1) A capacitor connected to this pin as shown in Figure 5 determines the gain of the on-chip photo amplifier during pushbutton test and chamber sensitivity test (high gain). The capacitor value is chosen such that the alarm tripped from background reflections in the chamber during pushbutton test. AV = 1+(C1/10) where C1 is in pF. CAUTION: The value of the closed-loop gain should not exceed 10,000. Resistor R15 should be installed in series with C1 for lower gains. R15 =[1/(12C1]-680 where R15 is in ohms and C1 is in farads. C2 (PIN 2) A capacitor connected to this pin as shown in Figure 5 determines the gain of the on-chip photo amplifier during pushbutton test and chamber sensitivity tests. AV = 1+(C2/10) where C1 is in pF. This gain increases about 10% during IRED pulse, after two consecutive local smoke detections. For proper compensation, resistor R14 must be installed in series with C2. R14 =[1/(12C2]-680 where R14 is in ohms and C1 is in farads. DETECT (PIN 3) This input to the high-gain pulse amplifier is tied to the cathode of an external photodiode. The photodiode should have low capacitance and low dark leakage current. The diode must be shunted by a load resistor and is operated at zero bias. The Detect input must be ac/dc decoupled from all other signals, VDD and VSS. Lead length and/or foil traces to this pin must be minimized also. See Figure 3. The device has a sampling speed-up mode after the first smoke sample is detected. The speed-up frequency is one smoke sample about every 2 seconds for the duration of a smoke condition. It will take no-smoke samples to return to a standby mode. Once out of a smoke condition, the IC will continue to sample for smoke about every 8 seconds. STROBE (PIN 4) This output provides the strobed, regulated voltage referenced to VDD. The temperature coefficient of this voltage is 0.2%/C maximum from -10 to 60C. The supply-voltage coefficient (line regulation) is 0.2%/V maximum from 6.0 to 12 V. Strobe is tied to external resistor string R8, R9 and R10. VDD (PIN 5) This pin is connected to the positive supply potential and may range from +6.0 to +12 V with respect to VSS. CAUTION: In battery-powered applications, reversepolarity protection must be provided externally. output voltage is typically +0.5%/C from -10 to 60C. The supply-voltage coefficient (line regulation) is 0.2%/V maximum from 6.0 to 12 V. The IRED pulse width (activehigh) is determined by external components R1 and C3. With a 100 k/1500 pF combination, the nominal width is 105 s. To minimize noise impact, IRED is active near the end of strobe pulses for smoke tests, chamber sensitivity test, and pushbutton test. For the above mentioned width, IRED will be active for the last 105 s of strobe pulse. I/O (PIN 7) This pin can be used to connect up to 40 units together in a wired-OR configuration for common signaling. VSS is used as the return. An on-chip current sink minimizes noise pickup during non-smoke conditions and eliminates the need for an external pull-down resistor to complete the wired-OR. Remote units at lower supply voltages do not draw excessive current from a sending unit at higher supply voltage. I/O can also be used to activate escape lights, auxiliary alarms, remote alarms and/or auto-dialers. As an input, this pin feeds a positive-edge-triggered flipflop whose output is sampled nominally every 1 second during standby (using typical component values). Once the first I/O remote smoke sample is detected, a second sample approximately 10 ms later will happen to confirm a remote smoke condition. If both samples are found to be high, the unit will start sounding an alarm. I/O is disabled by the on-chip power-on reset to eliminate nuisance signaling during battery changes or system powerup. If unused, I/O must be left unconnected. BRASS (PIN 8) This half of the push-pull driver output is connected to the metal support electrode of the piezoelectric audio transducer and to the horn-starting resistor. A continuous modulated tone from the transducer is a smoke alarm indicating either local or remote smoke. A short beep or chirp is a trouble alarm indicating a low supply or degraded chamber sensitivity. A series of short beeps or chirps during a pushbutton test indicate a previous alarm for detected smoke (Alarm memory feature). SILVER (PIN 9) This half of the push-pull driver output is connected to the ceramic electrode of a piezoelectric transducer and to the horn-starting capacitor. FEEDBACK (PIN 10) This input is connected to both the feedback electrode of a self-resonating piezoelectric transducer and the hornstarting resistor and capacitor through current limiting resistor R4. If unused, the pin must be tied to VSS or VDD. LED (PIN11) This active-low open drain output directly drives an external visible LED at the pulse rate indicated below. The pulse width is equal to the OSC period.
IRED (PIN 6) This output provides pulsed base current for external NPN transistor Q1 used as the infrared emitter driver. Q1 must have a 100. At 10 mA, the temperature coefficient of the
MC146012 Sensors Freescale Semiconductor 9
The load for the low-supply test is non-coincident with the smoke tests, chamber sensitivity test, pushbutton test, or any alarm signals. The LED also provides a visual indication of the detector status as follows, assuming the component values shown in Figure 4: Standby (includes low-supply and chamber sensitivity tests) -- Pulses every 32.4 seconds. Local Smoke -- Pulses every 2.0 seconds (typical) Mute -- Pulses every 2.0 seconds (typical) Remote Smoke -- No Pulses Pushbutton test -- Pulses every 2.0 seconds OSC (PIN 12) This pin is used in conjunction with external resistor R2 (7.5 M) to VDD and external capacitor C3 (1500 pF) to VDD to form an oscillator with a nominal period of 7.9 msec (typical). R1 (PIN 13) This pin is use din conjunction with resistor R1(100 k) to pin 12 and C3 (1500 pF, see pin 12 description) to determine the IRED pulse width. With this RC combination, the nominal pulse width is 105 s. VSS (PIN 14) This pin is the negative supply potential and the return for the I/O pin. Pin 14 is usually tied to Ground. LOW-SUPPLY TRIP (PIN 15) This pin is connected to an external voltage which determines the low-supply alarm threshold. The trip voltage is obtained through a resistor divider connected between the VDD and LED pins. The low-supply alarm threshold voltage (in volts) = (5R7/R6)+5 where R6 and R7 are in the same units. TEST/MUTE (PIN 16) This input has an on-chip pull-down device and is used to manually invoke a test mode, a mute mode, or a calibration mode. The Pushbutton Test mode is initiated by a high level at Pin 16 (usually a depression of a S.P.S.T. normally-open pushbutton switch to VDD). After one oscillator cycle, the IRED pulses approximately every 1.0 second, regardless of the presence of smoke. Additionally, the amplifier gain is increased by automatic selection of C1. Therefore the background reflections in the smoke chamber may be interpreted as smoke, generating a simulated smoke condition. After the second IRED pulse, a successful test activates the horn-driver and I/O circuits. The active I/O allows remote signaling for a system testing. When the Pushbutton Test switch is released, the Test input returns to VSS due to the on-chip pull-down device. After one oscillator
cycle, the amplifier gain returns to normal, thereby removing the simulated smoke condition. After two additional IRED pulses, less than three seconds, the IC exits the alarm mode and returns to standby timing. The Pushbutton Test will also activate the Alarm Memory feature. If there was a previous alarm detected by the unit, the horn will chirp every 1/4 second as long as the Test Button is pressed. Upon releasing of the Test Button, Alarm memory will be reset. Subsequent pressing of the Test Button will result in a Pushbutton Test for simulated smoke. Pressing the Test Button while in the MUTE mode will result in resetting of MUTE (and additionally a normal Pushbutton Test). The MUTE mode (IMF) is initiated by a mid level voltage (around 1/2 VDD) at pin 16. A parallel Mute Button to an existing Test Button needs to be installed at the test pin. A smoke condition must be present for the MUTE mode to be activated. If a no smoke condition gets detected while in the MUTE mode, the IMF 8 minute window gets reset. The unit will return to Standby mode. Once in the MUTE mode, the audible smoke alarm (horn) is temporarily disabled for approximately 8 minutes while smoke condition is being detected. A visual smoke alarm will remain (LED flashing) during MUTE mode. A high smoke voltage reference will also be activated at this time. Simultaneous smoke and high smoke sampling will allow the unit to enable the horn driver in case a high smoke condition occurs during MUTE where the high smoke threshold is crossed. The MUTE mode can be overridden by the following conditions: 1) a no smoke condition is detected, 2) high smoke level detected, 3) remote smoke detected through I/O, 4) reset through test Button, 5) timeout of 8 minute window. To help prevent a jammed Mute Button condition, the divider string on the Mute Button should include a resistor to VDD, R15 (around 10 M) and a resistor R16 (4.7 M) and capacitor, C7 (0.047 mF) in series to VSS. CALIBRATION To facilitate checking the sensitivity and calibrating smoke detectors, the MC146012 can be placed in Calibration mode. In this mode, certain device pins are controlled/reconfigured as shown in Table 4. To place the part in Calibration mode, Pin 16 (Test/ Mute) must be pulled below VSS pin with 100 A continuously drawn out of the pin for at least one cycle of the OSC pin. To exit this mode, the Test/ Mute pin is floated for at least one OSC cycle. In the Calibration mode, the IRED pulse rate is increased. An IRED pulse occurs every clock cycle. Also, Strobe is always Active Low. It is recommended to short R12 (Figure 5) in this mode. This will allow for a similar recovery of the emitter circuitry as in normal operation. Pin 1, pin 2, and pin 12 should be buffered with a unity gain amplifier to measure their outputs.
MC146012 10 Sensors Freescale Semiconductor
Table 4. MC146012 Test Mode Logic Table
Pin Pin 16, TEST Pin 12, OSC CAP Function Test Mode 1 Trigger Clock Input Type Input Input Logic None 0 1 Pin 5, VDD Pin 14, VSS Pin 11, LED Pin 4, STROBE Pin 6, IRED Chip Power Chip Ground Built-in-Test for HUSH Timer Analog Ground IRED Output Output Output 0 1 Pin 3, DETECT Smoke Sensing Input Input Output pulse active low for 8 Clocks every 128 Clocks. Output low when pin 12 is low. Output low when pin 12 is low. Output high (3.0 V) when pin 12 is high. NO SMK: VDD-2.5 V - (1/Hi Gain) SMK: VDD-2.5 V -(1/Low Gain) HI SMK: VDD-2.5 V - (2/Low Gain) Pin 8, BRASS Smoke Latch Indicator Output 0 1 Pin 9, SILVER Photo-Comparator Indicator Output 0 1 Pin 7, I/O Photo-Amp Routing Enable Input 0 1 Pin 15, LOW_BATT Pin 10, FEEDBACK Low Battery Trip Point Feedback Input Input Output low when smoke latch not set. Output high when smoke latch set. Output low when photo comparator not set. Output high when photo comparator set. Disable the function of Pin 1, 2, 10 and 15 in Test Mode 1. Enable photoamplifier output routed to the pins and enable pins 1, 2, 10 and 15 in test Mode 1. Control photo amp. Gain and output routing Control hysteresis Description Set a -Ve voltage to the pin and source 100 A from the pin to start Test Mode 1. Internal clock low Internal clock high
MC146012 Sensors Freescale Semiconductor 11
Figure 6. Recommended PCB layout
MC146012 12 Sensors Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 1 OF 3
98ASB42431B ISSUE T PLASTIC DIP
MC146012 Sensors Freescale Semiconductor 13
PACKAGE DIMENSIONS
PAGE 2 OF 3
98ASB42431B ISSUE T PLASTIC DIP
MC146012 14 Sensors Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 3 OF 3
98ASB42431B ISSUE T PLASTIC DIP
MC146012 Sensors Freescale Semiconductor 15
PACKAGE DIMENSIONS
PAGE 1 OF 2
98ASB42567B ISSUE F SOIC PACKAGE
MC146012 16 Sensors Freescale Semiconductor
PACKAGE DIMENSIONS
PAGE 2 OF 2
98ASB42567B ISSUE F SOIC PACKAGE
MC146012 Sensors Freescale Semiconductor 17
How to Reach Us:
Home Page: www.freescale.com E-mail: support@freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 +1-800-521-6274 or +1-480-768-2130 support@freescale.com Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) support@freescale.com Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com
Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc., 2007. All rights reserved.
MC146012 Rev. 1.0 5/2007

▲Up To Search▲

Price & Availability of MC14601207

	To Download MC14601207 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .